Menu

How to Make a Desk with Hidden Wireless Charging

100 Comments



What’s up guys, I’m Brad Rodriguez from Fix This Build That and today I’m going to show you how to make a desk with hidden wireless charging I’m also going to show you a tip on how I install this metal copper inlay into the desk. Stay tuned I’ll show you exactly how I did it I’ve had this stack of walnut boards in the back of my shop for a couple years now Just waiting for the right project And since I’m going with a simple metal base for the desk And I thought this was the perfect time to dip into the stash for a couple boards to make an amazing top I’m going with a 20 inch desktop to try and minimize clutter that will land on it So I cut the rough boards in half to give me four boards for the top When working with rough lumber you can get some pretty twisted boards like this and one of the things that helps before milling is to knock down the high spots on the opposite corners of the Board with a block plane this removes some of the rocking it makes milling go a little smoother but to get the rest of the twist out of the board’s I took them to the jointer and face jointed each board it basically does what I just did with the hand plane, except a whole lot faster and more consistent after a few passes I got down to fresh wood and the board now sat flat on my bench. I ran the other three boards through the jointer as well to get one flat face on each board before moving on to the planer Using the flat face from the jointer I ran each board through the planer until the mill marks were removed and I revealed fresh-cut wood, which looked amazing I finished the rough milling back of the jointer by putting a straight edge on each board Then I cut the board’s a little larger than final width at the table saw Now if you don’t have these rough milling machines You can buy nice walnut lumber like this already surfaced from many woodworking stores locally and online. I labeled each board to keep them organized and then I went into the first glue up Instead of gluing all four boards together. I glued up to smaller halves This is gonna let me flatten the pieces on my planer into a final glue up then I’ll just have to worry about one seam instead of three After the glue is dry on the first glue up I took the halves out of the clamps and brought them back over to the bench to fill some of the defects in the wood with epoxy Some of the knots and cracks went all the way through the boards So I taped them off on the back side to keep the epoxy from leaking out Then I’m small portions of a two-to-one clear epoxy with a slow hardener and started to fill the defects in Their words a lot to fill including a huge void on the bottom side and some nice little bug holes. These guys had a feast After the epoxy dried I knocked down a few high spots with my block plane Then I ran each half through the planer until I got the fresh wood all over again Now this is where using the two halves really comes in handy It eliminates a lot of epoxy scraping as I just send that thing through the planer and let it do the work To prep for the final glue up I took the sections to the jointer and ran each one across to get a pair of nice straight edges. I glued the halves together just using clamps to line everything up I get asked this all the time And yes, the glue joint alone is more than strong enough to hold the top together You don’t need any screws dowels biscuits dominoes or any of that While I was waiting on the top to dry I moved over to make the base I’m using one inch tube steel for the base and I haven’t really gotten fully set up with metal cutting equipment yet So I had my local metal yard cut it to the exact size for me, which was a huge time-saver. I mark, the joint connections and I used a flat disc on my grinder to prep the metal for the welding Like I said, I’m new and I’m still trying to figure things out but my welding table setup is a bit rudimentary but my welder on the other hand is the 210 MP from Lincoln Electric and it is smart enough to set the wire feed and The voltage for me based on just a few inputs It takes the guesswork out of the welding and as a beginner, I really appreciate that You can find out more about the 210 MP and a link down below in the description I started by welding together the rectangular ends of the desk first. I tacked them in place Then I ran a bead of weld around each side of the joint I also quickly realized that clamping the parts down as tight, as you can was key to a square joint These little magnetic squares are more like a suggestion of keeping things square. I worked my way through the welds and I ended up with two ends ready to be joined together But before joining the ends together with the long stretchers I ground down the weld joints with a flat disc on my grinder again here when you’re welding You really want to have nice fresh clean metal since the desk is so large I had to move it to the ground and use these magnets to hold things in place. I tacked in Well the back of the desk first checking Foursquare along the way Then I flipped it over and welded the top front stretcher in place to complete the frame I’ve got to say I really enjoyed welding a full project by myself This was only the second welding project that I’ve really ever done And this is the first time I’ve done it solo in my own shop I got better as I went, but I still have a ton to learn So hit me up with your welding tips in the comments. Let me know what I’m doing wrong and how I can get better To finish off the base. I wanted to add some tabs to screw down the top I got some one-inch angle iron and I laid out six tabs of the marker After marking each tab. I took the angle iron to the drill Press and I drilled an oversized hole for the screws after that was done I took the angle iron outside and I cut the tabs apart with an offcut wheel on my grinder After cleaning the tabs up a bit with a flap disc. I turned the base upside down and I tacked each tab into place Oh, and welding 101 don’t weld your clamps to the work cheese. I Prep the base for paint by grinding all the weld joints smooth and I sprayed on a couple coats of self-etching primer I FolIowed up with several coats a flat black enamel and matte clear coat now by this time the top was all ready to go So I took it out of the clamps and I cut it down to final width By joining a straightedge on one side and then cutting it to final width on the table saw To cut the top to length I used my circular saw I Put painters tape on the top side and then I turned the panel upside down Now both of these things are gonna help prevent tear-out from the circular saw cut I laid out my cut line with a carpenter’s square. You know, I made the cut with my track guide. I Spun the top around and I made the second cut Which made the top to final length and I had exactly what I was looking for I’m loving the new wireless charging feature on my phone, but I don’t like having the extra wires on my desk So embedding the charger on the bottom was a great alternative I traced the shape of the charger and then I used a router to remove the waste free hand And since I don’t have a plunge router, I drilled a starter hole with a Fortuner bit And then I started the router in the middle and slowly circled outward until I hit that layout line that I had traced After confirming the fit I took another pass taking about 3/8 of an inch off at a time I also routed a little recess pointed towards the back so I could fit the USB plug for the charger for the final past I use an eighth of an inch piece of scrap to position the bid I Tested the charger through this material and it’s still charged. So I figured I would be good to go with this depth After I was done I couldn’t wait to test it out So I put the charger into the slot Flipped over the top and held it in place with one hand and then the moment of truth I Was pretty stoked it actually worked even with this case that’s on my phone I’ll link the charge that I used down below If you want to use the same one To give the USB cable a sleek way to come out of the back of the desk. I cut a trench for the cable I used my smaller palm router and a quarter inch bit and just made one shallow path straight back to the edge of the top the test fit looked great and I flipped the top over and I sized up where the phone would sit while it was charging and Hey if this is your first time visiting my channel Welcome if you like what you see be sure to subscribe and hit that bell to get notifications when I upload new videos thanks a lot and hope to see you around I Wanted an easy indicator to know where to put the phone in Nick Kyle from Blackbird machinist sent me this awesome Copper bowtie a while back So I figured it would make a perfect accident and give a reference for the charger at the same time. I Positioned the bowtie where I want it and then jumped into the inlay now I’ve never done any inlays like this and I was pretty scared to do it, honestly I didn’t want to ruin the top because I just worked so hard on it but I made a couple test runs in scrap wood and then I just dove in I used some double stick tape to hold down the bow tie and then I scored an outline with a razor blade and I set my Palm router to the thickness of the inlay and routed out the majority of the waste staying pretty far away from the lines And then comes the time-consuming part of cutting to the line I Really took my time here because I knew with metal that I wouldn’t be able to fill the gaps as easily as if it were A wooden enlight and only had one shot at it and the rest of the work is done with chisels I just switched back and forth between my 1 inch chisel Which I used to make long straight cuts and the smaller chisels which remove material a little easier since there was less cutting surface Just take your time here again, and finesse it until you get the right fit When I was done I mixed up some epoxy to hold the inlay in place and I spread it on the bottom of the recess I used a scrap block of wood on the inlay and tapped it into place I actually think I put a little too much epoxy in and it caused the inlay to be just a little proud of the surface So flush everything up I started with sixty grit paper and stain of the copper until it was flush Then I work my way up through the grits this took a long time So I would err on doing it too deep with a metal inlay versus too shallow in the future And now is the part that I’ve been waiting for ever since I milled this walnut for the finish. I’m using fast-drying polyurethane From Minwax a sponsor of today’s video and it’s an oil-based durable protective finish that really makes this walnut look amazing and since the desk surface is gonna get a ton of wear this tough polyurethane finish is perfect for the job I applied one thick coat with a foam brush and then I came back later with a thin down second coat to get that nice Smooth finish you can find out more about the fast-drying polyurethane via the link down below in the description When the finish was dried it was time to install the charger I opted for a quick and easy Mounting by just hot gluing it in and don’t be a goon here and hot glue all over the wire It just makes a mess put those glue in the channel and then press the wire into it you live and you learn I Finished off the assembly by flipping the base onto the top and mounting it with 3/4 inch screws Then I tapped in some plastic feet into the vertical steel tubes and I was done This desk came out way better than I ever imagined it Would I got to try out a lot of new techniques with this one that stretched my skills as a woodworker and a metal worker? And on top of it all I got a desk that has a ton of character and wireless charging That’s out of sight and always on the ready If you’ve loved this video, I think you’re gonna love that one to go. Check it out I got another one queued up there for you. If you’re not subscribe to the channel already I’d love to have you as part of the team and until next time guys get out there and build something awesome

Tags: , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

100 thoughts on “How to Make a Desk with Hidden Wireless Charging”

  1. Mouad Meziani says:

    in first i thought he will make the whole table wireless charging for the PC ,mouse and phone

  2. Parsa's Life says:

    you know you can use crafting table and use a bunch of sticks to craft this with a press of a button?

  3. 10000 subs with No videos says:

    When I’m welding I don’t wear a helmet

  4. Digital Veeskys says:

    Wow. This was an awesome vid. Great work.

  5. チャッドリー 龍介 says:

    watching this video on a device with no wireless charging

  6. チャッドリー 龍介 says:

    how much will u sell it for

  7. Emanuel Xocua says:

    I’m poor I don’t even have a phone or a laptop idk why I’m watching this lol.:(

  8. Tryeasy. says:

    Why did you use a Samsung

    Jk

  9. Rohan says:

    That's damn easy !

  10. Ian Miller says:

    Great! ANOTHER thing I'm never going to build!

  11. Black Bird says:

    I still see a wire

  12. Joseph Grey says:

    Hold on guys, let me plug in my desk

  13. daniel nadir-gopro karma says:

    coooolllllll …… nice

  14. SYRA Quint says:

    This is ma first time. I found your channel bcs i miss my dad. my dad often do the same think like that. Btw sorry for my writing not good, Thankyou for a great video👍🏼

  15. Rishabh Jaiswal II says:

    Or make a small hole in the table and put the wires down from that holes ?

  16. Nutterie says:

    and that, fellas, is what you can achieve when you are rich

  17. Tamir Ali says:

    let's see what a chisel, knife and a hammer can do

  18. alex MAN INNIT says:

    Did anyone else think the entire table was going to be wireless and is now some reason slightly disappointed?

  19. Quinlan Harsch says:

    To sum up what I remember, because Qi Wireless charging wasn't standardized early on, different phones require different coil sizes. Many generic chargers use several coil sizes so a variety of brands work with them, leading to wasted electricity. IDK what Minwax and Lincoln Electric stocks, but if they have something specific to your brand of phone, buy that one.

    Or don't, I'm not your mom.

  20. The Man says:

    What do you use to keep sawdust from going everywhere?

  21. Matthew Griffin says:

    wow, only thing that would make this better is if he cut the dang tree down himself!

  22. Vaibhav Thamman says:

    You did everything right so nice and clean. But then you super glued the charger and wire. 😷

  23. Luis Engleton says:

    If you sold this I would buy it, no questions asked

  24. Habanero Jones says:

    I paused the video a few times before I realized…I'm sitting here watching like I'm going to actually try to build a table. "Right. Oh yeah, that's a good idea. Of course! That's what I thought too…dafuq is wrong with me?"

  25. vilusha says:

    Can it charge iPhone 6?

  26. 2tone_brazy says:

    Thatss dooope 🔥🔥🔥

  27. aL Quarter says:

    As if everyone has all these tools 😂😂

  28. Bris Vegas says:

    ever heard of radiation?

  29. Itz Titan says:

    Welp the charging process will take ages now… and my phone doesn't support wireless charging… soooo

  30. Storm Tuber says:

    80% of the video is making the table 5% of the video is just flying in a store bought wireless charger underneath it, 10% is a copper logo and 5% is telling people to subscribe

  31. Aaliyah Brocket says:

    Who watches the video but never does it ?

  32. AKASH MADHAVAN says:

    good

  33. Aaron Michaelson says:

    This is awesome. I love the bowtie emblem in the surface. Hopefully your charger pad doesn't overheat and is able to last a while within your table! I probably would have cut about 1" of extra hole radius so it at least gets airflow around the sides of it. But if it works, it works.

  34. Viqix says:

    I bet 99.9% that are watching this video aren’t going to actually make this 😂 who else jus t likes to watch videos like this

  35. Basti on GS says:

    Wow. Wish i could do this.

  36. 7s7s says:

    1-get a wireless charger
    2- hide it

  37. Bogart E says:

    You’re so talented & cute 😉

  38. william walker says:

    If your phone charger stops working how are you going to switch it out?

  39. Andrew G. says:

    first video ive seen and I already subbed

  40. Prashant Sah says:

    Wireless charging worst invention ever.. You waste a lot of power and still can't get rid of that wire bcoz it is connected to charging pad and you need to keep phone on your pad..

  41. Aaron McDaniel says:

    Hows the flash burn on you legs lol

  42. Shovan Karmakar says:

    excellent job

  43. Gun Nation says:

    EZ subscription 👍

  44. Jay Bizz says:

    Very nice!

  45. Greg Daines says:

    I loved the clean design of this

  46. James Brooke says:

    I thought he was going to take a ton of wireless chargers and put them all throughout the desk. Guess not.

  47. Jamie Croft says:

    Like i have all that stuff??😑😒

  48. Jamie Croft says:

    Imagine wanting the charger in a differnt spot after just finishing

  49. Wolf Gun7 says:

    Weling tip
    me: u kidding me,haven't even touch 1

  50. Garrett Moore says:

    when i heard you say the glue joint is more than strong enough i remembered a longboard i made that it snapped right next to the glue seam XD

  51. N Mag says:

    а че делать, если инструментов таких нет??

  52. Omesh Sahoo says:

    Oh my god this has been in my recommenced for so long and I finally gave up and watched

  53. s J says:

    I was watching this because I thought it was a quick fix for any desk….boy was i wrong lol

  54. EpicLaith says:

    Or just buy one from ikea

  55. Matthew Stevens says:

    Gets an iPhone

  56. glimpsertube says:

    Super

  57. Insane Tube says:

    Cool i just copied it .. with my brother hahah ..

  58. WSNXFREAK says:

    i love your desk!!!!

  59. goha chi says:

    youtube recommended this vid out of nowhere but gotta say, i had no regrets clicking it!!! your creations are awesome!! tho i dont understand most terms used in your videos your explanation is easy to understand 😀

  60. Daily dose Of youtube says:

    the desk is better than you imagined it wood hahaha get it

  61. tapiado1 says:

    It really doesn't matter how you weld if the result is good.

  62. Alex jones says:

    A desk with built in cancer? I'll take mine black.

  63. Ghost Jet says:

    Damn bro that came out awesome, you should be proud of yourself, I need to get my hands on some walnut board's. I thought ur welding worked out just fine and the top came out beautiful, great job! I think I will be making a desk for my office pretty similar to yours, so thanks for the tips and tricks!

  64. Farty Buttspoop says:

    Welding tip: wear long pants

  65. Sebastian Hinestrosa says:

    who clicked on this video thinking they were gonna be able to do this on your own with ease?

  66. Danny Izoita says:

    DONT WELD ON CONCRETE!!! It could explode

  67. tony smarks says:

    maybe some rgb lighting on the chargins area.

  68. Tenzin Kunsel says:

    Better than ikea.

  69. Shawn Chavis says:

    Option 1: Have a shop with $10,000 worth of tools, have skill, and have time. Option 2: Buy a wireless charging desk.

  70. Tomas Aguilera says:

    awesome

  71. Spencer says:

    What I would've done with the copper inlay was put it right above the charger so there would be no guesswork involved at all

  72. mike says:

    i really appreciate the attn to detail w/ the process, its so cool to see everything being done!
    also i wish i had that desk!!

  73. beykoz 1908 says:

    good

  74. Jake Malone says:

    i wish i can do this. but my desk is granite 🙁 but its a really nice desk lol

  75. Dr. Saad Javaid says:

    I have an iPhone, what am I even doing here?

  76. Jojo says:

    Who’s watching this knowing u will never do anything like this ?

  77. Bilal Pervaiz says:

    Amazing & Great Idea,
    Liked, Subscribed, Shared
    Keep up the good work,
    Best Regards

  78. notsean says:

    wow this guy is so cool!

  79. Colin says:

    when you weld, even with mig don't do a circle pattern and just do a zigzag pattern at a little slower pace. you'll get better penetration and you won't have flux inside of your weld pool. just a tip, I wish i had a welder that nice.

  80. Conrad Larson says:

    That turned out amazing!

  81. tupachussain says:

    Absolutely amazing well done

  82. camalama21 says:

    Just beautiful, great work!

  83. Dann Taylor says:

    I absolutely need to build a desk similar to this. Love that hour glass inlay, perfect finishing piece to that gorgeous walnut

  84. Cherry Marry says:

    how much

  85. Marcelo Matiello says:

    Come on man. For a learner this looks super professional. great job

  86. hippos_gaming 548 says:

    Drinking ginger soda and watching youtube.

    Life. is. cool.

  87. Deku Irkift says:

    poor me i tot it was simple like 5min craft

  88. Marcin Rzepa says:

    I just want a wireless charger. Hey let's make a table👍😉

  89. Vats pk says:

    How to make a table with built-in wireless charging
    Me-Readinng comments rather than watching video 😋

  90. Vats pk says:

    Seriously using that much of tools …
    Come in INDIA bro…less tym same work or may even better😂😂i didn't ever watch these type of tools😂

  91. Muntasib Maroof says:

    seems like an easy task. but not easy for those who have not that instruments like you have. Especially in Pakistan.

    Btw your welding machine is too good as well as your technique.

  92. Hamir Bharwad says:

    I love it… if u have done it differently, I mean we are not here to see how u make table or what type of coatings you have done on your table.. Because non of us going to build the table or has equipment what you have..

    we wanted to know how to make wireless charging on table..

    I love if you have removed that copper coils from 3 to 5 wireless chargers and placed it on the different side of the table (not underneath) and then use/apply clear epoxy resin on it..

    This will be something different from others.

  93. Dr. Lightz says:

    Hello, can i get a hug? 🤗

  94. Omar El-Alamein says:

    Or just tape the wireless charger to a a desk you already own.

  95. Victoria Hesenflow says:

    That was great.

  96. Tim Mcmillan says:

    I like everything about your video and idea except the thought of gluing in the charger what will you do when you need to replace it which is inevitable

  97. 이종도 says:

    What kind of product is fixed ruler? time table 07:10

  98. Mr Soham Gear says:

    Great idea brother

  99. COLORS and TASTES says:

    Can someone tell me please, what's this laptop on the Desk? Thanks

  100. Syaz Rios says:

    Idk why i watch this kind of video whenever i feel sad .Lol am i weird

Leave a Reply

Your email address will not be published. Required fields are marked *